Pelican Parts Technical Articles Main Image

Jacking Up Your Porsche Boxster or 996

  • Parts Required: Hockey pucks (4), Pelican Parts custom floor jack adapter
  • Performance Gain: Safely jack up your Boxster or 996 while protecting your undercarriage's finish
  • Complementary Modification: Always use wheel chocks

     Periodically, I like to jack up my car, get under it, and look it over carefully.

 I check for loose fasteners, damage to the undercarriage or suspension, and exhaust leaks.  This is also a good opportunity to look for oil, coolant, or brake fluid leaks.  For personal safety, I always support the car with jack stands before I get under it.

     The Boxster or 996 requires a slightly different approach to jack it up.  The jack points are oval-shaped sockets in the bottom of the car, and the underside of the car doesn't have any obvious places to put jack stands.  Pelican Parts now offers a custom floor jack adapter, specifically for the Boxster and 996, which allows the car to be jacked up safely.  It comes in a nice zipper bag for storage (Figure 1), and it has an extended tang that fits exactly into the jack socket (Figure 2).  The adapter even has a tough rubber pad to prevent marring the undercarriage (Figure 3).

     If your floor jack is like mine, it is too tall to fit under the Boxster without removing the saddle from the jack.  The saddle on my jack just lifts off, and then the jack fits nicely under the car, using the new adapter (Figure 4).

     I was reluctant to use jack stands with bare metal tops on my new Boxster.

     I decided to pad the top of each jack stand with a hockey puck (Figure 5).  I attached the puck to the jack stand by drilling a 6mm hole through it, with a slight countersink.  I then drilled and tapped a hole in the top of each jack stand, and attached the hockey pucks using 6mm X 30mm bolts.  The pucks are very hard rubber, so they should hold up well, but still conform to the shape of the jack socket (Figure 6).

     With this setup, I can jack up my Boxster without damaging anything, and feel safe while working underneath it.  It isn't due for an oil change yet, but I'll be ready for that, too.


Help support this site with your purchases.  Although this product is not yet featured in our on-line catalog, you can order it from our sales department by calling us at 1-888-280-7799.

Wayne R. Dempsey, Co-Founder & DIY Expert

Bob Tindel, DIY Expert

//

Project Photos

Placeholder Alt Text
Figure 1
Placeholder Alt Text
Figure 2
Placeholder Alt Text
Figure 3
Placeholder Alt Text
Figure 4
Placeholder Alt Text
Figure 5
Placeholder Alt Text
Figure 6

Comments and Suggestions

Valentina

February 9, 2024


you made it easy.

Followup from the Pelican Staff:

Thanks for the feedback. Glad it was helpful! - Nick at Pelican Parts

Jim O

April 9, 2020

Your Pelican Technical Articles are GREAT! I was installing new brake pads on my 2001 Boxster S and the new pads did not have holes for the brake pad sensors. I quickly found the solution at Pelican. The technical article contained a simple sensor bypass solution along with very clear pictures. With Pelican's help, the problem was solved in minutes. Thanks Pelican!!!

Followup from the Pelican Staff:

Thanks for the feedback. Glad we could help. - Nick at Pelican Parts

Fatbloke

August 21, 2014

Jacking up at the front looks straight forward from your photo and leaves the support points free for the axle jack stands but can you show some pictures of where to jack the rear up so that the rear support points are free for the axle stands? 2004 2.7 Boxster Could the car be jacked up on the sills or would the sill seams just fold?

Followup from the Pelican Staff:

Try this tech article: https://www.pelicanparts.com/techarticles/Boxster_Tech/01-BASICS-Jacking_Up/01-BASICS-Jacking_Up.htm - Nick at Pelican Parts

pfeffers

November 17, 2012

Very confusing - does not provide the steps or sequence in jacking up the car and placing the jack stands. i assume some sequencs of jacking from one jack point raises the car enough to place a jack stand beneath another jacking poin???

Followup from the Pelican Staff:

Wayne offers some insight here: In response to the previous comment - I like to jack the car up by the rails that run underneath, and then place the jack stands under the specified jacking points. See the photo I've attached. - Nick at Pelican Parts

Alex

March 16, 2012

I just read your tech article on jacking up your Boxster. I'm a little confused. If you are jacking up one side with a floor jack, where do you put the jack stand?? Are there 2 jack points on each side that allows you to use the floor jack to lift the car on one jack point and another jack point for the stand?? Then lower the floor jack and do the other side.
Also why do you need a 27mm socket to do and oil change.
Is it for the drain plug??

Followup from the Pelican Staff:

Wayne offers some insight here: In response to the previous comment - I like to jack the car up by the rails that run underneath, and then place the jack stands under the specified jacking points. See the photo I've attached. - Nick at Pelican Parts

George

January 28, 2012

Re 996 Jack Stand Adapter.
Could you kindly supply me with the jack stand adapter for our 996 and possibly our 968 Cab? as mentioned in your Pelican Technical Article ?

Followup from the Pelican Staff:

You can grab one here: https://www.pelicanparts.com/cgi-bin/ksearch/PEL_search.cgi ?command=show_part_page&please_wait=N&make=POR&model=996J§ion=UPG996&page=11&bookmark=7&part_number=PWE-FJP-003 Or give our parts specialists a call at 1-888-280-7799. They can help you find the right adapter. - Nick at Pelican Parts

bhj951

May 9, 2011

On my 944 Turbo there was a jacking point between the wheels, allowing you to lift the entire side of the vehicle in one go, and place stands front and back. Does the Boxster have this capability?

Followup from the Pelican Staff:

Sortof - you can jack in the middle of the car, and it will lift on one side. But the back will dip down a bit. I prefer the four-point jacking method detailed in the article. - Wayne at Pelican Parts

Tom

October 16, 2010

I once saw a bag that zippered that I could drive my 944 turbo in to store it for the winter

Do you know where I can find this zippered bag

Followup from the Pelican Staff:

I haven't seen those. We have some nice covers. Give our parts specialists a call at 1-888-280-7799. They can help you find a cover. - Nick at Pelican Parts

Bob

August 5, 2009

I cannot figure out the scheme you describe. If the jack uses the jack point to lift the car, how is the jack stand placed at the jack point?

Followup from the Pelican Staff:

Yes, this article is slightly confusing with respect to that. I have another article coming out for my new book that clarifies this, I posted a preview copy here: https://forums.pelicanparts.com/showthread.php?t=446236 Basically, I jack from the inside support rail and then put the jack stands over the jacking point. - Wayne at Pelican Parts

coppersmith99

June 4, 2009

Standard set of light-duty stands with a low-profile jack from any automotive department work just fine without expensive after-market adapters or custom hockey puck modifications.

Followup from the Pelican Staff:

Thanks for the additional Info. We appreciate it. - Nick at Pelican Parts

Wayne at Pelican Parts

April 30, 2009

In response to the previous comment - I like to jack the car up by the rails that run underneath, and then place the jack stands under the specified jacking points. See the photo I've attached.

Followup from the Pelican Staff:

Thanks Wayne. - Nick at Pelican Parts

Placeholder Alt Text

bvmorton

April 30, 2009

Where do you place the jackstands? ...on the ridged seams? Where do you recommend? Thanks in advance...

Followup from the Pelican Staff:

Wayne offers some insight here: In response to the previous comment - I like to jack the car up by the rails that run underneath, and then place the jack stands under the specified jacking points. See the photo I've attached. - Nick at Pelican Parts

Add a New Comment
Upload a Photo:

Got more questions? Ask any of our automotive experts.